IC698PSA100 GE power supply module

IC698PSA100

IC698PSA100

IC698PSA100

IC698PSA100

IC698PSA100

IC698PSA100 is a versatile Power Supply Module manufactured by GE Fanuc for the RX7i series. This PACSystems module delivers +5 VDC, +12 VDC, and -12 VDC power as well as logic level sequencing signals to modules on the backplane. The module plugs straight into slot 0 in the main rack. The IC698PSA100 module’s power supply output can lose up to one AC input line cycle without actually losing output power. Overcurrent, overtemperature, and overvoltage fault conditions are also protected. The module allows 100 watts total output power at ambient temperatures of 0 to 60ºC with no forced air cooling.

Output voltages are as follows: +5 VDC output up to 20 amps, +12 VDC output up to 2 amps, and -12 VDC output up to 1 amp. Additional features of the IC698PSA100 module include operation from 85 to 264 VAC or 100 to 150 VDC and power factor correction for AC operation. This module is designed for simple slide-in rack mount construction.  The two-position On/Off switch is situated on the front faceplate. It is a logic level switch that enables or disables the output channels. This switch will not interrupt the AC line input. Please note: Lethal voltages are present inside the module when input power is present. The IC698PSA100 comes equipped with LED indicators to alert the user to both field and output status. These will turn ON when power is applied within the acceptable range and when DC output channels are operating correctly.

The IC698PSA100 is a PACSystem RX7i Power Supply module that is manufactured by Emerson Automation, formerly under GE Intelligent Platforms (GE IP). This power supply module mounts to the leftmost slot of any RX7i standard rack, specifically, slot 0. It comes with screw type input terminals, designed for input voltage rages of 85 to 264 VAC (nominal voltage of 120 / 240 VAC) with frequency of 47 to 63 Hz and 100-150VDC (nominal voltage of 125 VDC). External power connections must be made using AWG #16 (1.3 mm2) solid or stranded copper wire with insulation rating of 75°C (167°F). For ground connection, use #12 (3.3 mm2) copper wire with 75°C (167°F) insulation rating. Appropriate termination of GND connections may significantly eliminate if not, reduce system noise.

The IC698PSA100 delivers a maximum output power of 100 Watts which is the total for all Three (3) output terminals that delivers 4.875 to 5.25 volts, 0—20 amps, 5.1 VDC, nominal; 11.64 to 12.6 volts,, 0—2 amps, +12 VDC, nominal and –12.60 to –11.64 volts, 0—1 amps, -12 VDC, nominal. This power supply module features a ride through time of 15 ms, minimum and hold-up time of 5 ms, minimum. It is also provided with Proactive overvoltage and overcurrent limits, specifically, 5.7 to 6.7 volts overvoltage protection at +5VDC; 21A at +5 VDC output; 2.5A at +12 VDC output and 3.5A at -12 VDC output.

This power supply module has an operating temperature of 0°C to 60°C (32° to 140°F) with isolation rating of 1500 VDC.

1. What is the output power rating of the IC698PSA100?

The IC698PSA100 has a maximum output power rating of 100 Watts.

2. What are the output voltages of the IC698PSA100?

The IC698PSA100’s output voltages are +5.1 VDC; +12 VDC and -12 VDC.

3. What is the output current of the IC698PSA100?

This power supply has output current of 0-20 Amperes at 5.1 VDC; 0-2 Amperes at +12 VDC and 0-1 Amperes at -12 VDC.