IC698RMX016 VMIVME-5567-100 GE Redundant Memory Exchange Module

Description

IC698RMX016 VMIVME-5567-100 GE Redundant Memory Exchange Module

Can be transported to all parts of the world. (Exclude areas that cannot be transported under special circumstances! )

If necessary, please contact customer service.

Xiamen Xiongba Electronic Commerce Co., Ltd. Zhangzhou Branch Main Scope

Products are used in: electric power, petroleum, mine, port, heating, gas, water supply, sewage treatment, metallurgy, paper making, textile, chemical industry, water conservancy and other modern industrial fields!

Purpose: To create excellent quality and excellent service.

Business philosophy: “Honesty and pragmatism” is our constant business philosophy.

Company goal: Our goal is to give you the same product, but the difference is the superior price and attentive service.

Specializing in the world-renowned brand DCS system, robot system, large-scale servo control system and module.

IC698RMX016 VMIVME-5567-100

IC698RMX016 VMIVME-5567-100

IC698RMX016 VMIVME-5567-100

IC698RMX016 VMIVME-5567-100

IC698RMX016 VMIVME-5567-100

The GE Fanuc’s IC698RMX016 is a 16MB Redundant Memory Xchange for the Rx7I Pacsystem.  It has the following sizing: 6.299 inches widde x 9.187 inches high. It has 16MB of SDRAM user memory. The operating voltage from power supply is +5 V DC. Current requirements are 1.8A. The unit has a fiber optic LC type connector which, conforms to IEC 61754-20, and a zirconium ceramic ferrule. The maximum insertion loss is 0.35 dB with a return loss of -30dB. An acceptable temperature range is between -20°C and +85°C. To complete installation, you need to make sure you have all of the following: A PACSystems RX7i CPU with release 2.00 or later firmware; a PACSystems Rx7i CPU rack with power supply; a PC-compatible computer with CIMPLICITY Machine Edition – Logic Developer PLC, version 4.5 or later programming software and the necessary cables.

Note that in order to meet radiated emission standards, RX7i systems that include more than one Memory Xchange modules have to be installed in a conducting metal enclosure, or equivalent. Memory modules should only be installed in RX7i Rack 0 (main). It is advised that RMX modules are installed in slots 4 and 3 of the main rack. This provides the RMX modules VME interrupt request priority. Although such configuration is advisable, locating RMX modules in slots 4 and 3 is not strictly required. To install IC698RMX016 Redundant Memory Xchange, make sure the rack power is switched off. Next slide the module into the exact slot it was configured for in the system. Proceed to press the board in place without forcing it. Tighten faceplate top and bottom screws. Next make sure to connect cables to RX and TX connectors. The fiber optic cable should be routed from the TX connector to next node’s RX connector. Connect the that board’s TX cable to next node’s RX connector. Repeat until last node in the ring has its TX routed to the RX connector of the first node. Turn the power on.

The IC698RMX016 initially powers in a non-configured state where its optical transmitter is disabled. The Redundant Memory Xchange module will not operate on a network before the RX7i CPU sends the module a hardware configuration.  For the purpose of reflective memory operation, the user can choose to configure the following parameters: Redundant Transfer Mode, Node ID, Network Memory Offset, Rogue Master, and Interrupt enable. Note that if the Redundant Link operation is selected, the above-mentioned parameters will be set by the CPU and are therefore not configurable.  Note that when IC698RMX016 is used as a reflective memory module with a general purpose, additional functions that extend beyond the basic read and write operations, inclusive of reading interrupt status, enabling interrupts, reading parity errors, and enabling parity may be performed by user logic.

The IC698RMX016 communication module uses a high speed fiber optic network for data exchange. The front section of the module comes with 8 different LED indicators and with a toggle switch that can be used to authorize a role switch. The role switch is used to changes roles for the module and it helps to prevent accidental activation. It has 2 on and off positions. It has a spring loading mechanism that is in the off state by default. The IC698RMX016 module requires a PacSystem with firmware version 2.00 for installation. It uses the logic developer PC software for programming. The connector of the communication module is manufactured by using zirconium ceramic ferrule and it has an insertion loss of 0.35 dB maximum. It has a return loss of -30 dB. An optical transceiver is present in the module and it has 2 LC optic ports. There is a TX port for a transmitter and an RX port for a receiver.

1. What is the user memory available to the IC698RMX016?

The IC698RMX016 has built-in 16 MB SDRAM user memory.

3. What is the recommended mounting slot of the IC698RMX016?

Recommended mounting slot for the IC698RMX016 is slot 3 and 4

Xiamen xiongba

Please contact Sunny sales@xiongbagk.cn for the best price.

➱ sales manager: Sunny
➱ email mailto: sales@xiongbagk.cn
➱ Skype/WeChat: 18059884797
➱ phone/Whatsapp: + 86 18059884797
➱ QQ: 3095989363
➱ Website:www.sauldcs.com